Jewell — Layers of Luxury← All products
PRODUCT LIBRARY / Putty
PremiumIndian

Watertite Waterproof Wall Putty

Jewell Watertite Waterproof Wall Putty is a premium quality powder putty specially designed with silicone and anti-efflorescence additives to provide waterproofing properties and efflorescence resistance.

Explore product
SurfaceWalls
UseInterior and exterior
StatusAvailable
Watertite Waterproof Wall Putty packaging
JEWELL / PRODUCT COLLECTION
Watertite Waterproof Wall Putty packaging
Jewell · Premium

Watertite Waterproof Wall Putty

Jewell Watertite Waterproof Wall Putty is a premium quality powder putty specially designed with silicone and anti-efflorescence additives to pr…

Explore the product
THE PRODUCT STORYThe product story

Jewell Watertite Waterproof Wall Putty is a premium quality powder putty specially designed with silicone and anti-efflorescence additives to provide waterproofing properties and effloresce…

↗
Water repellencyProduct benefit
12–18sq. ft. coverageSee conditions below
Watertite Waterproof Wall Putty / THE NUMBERS

Made for life.
Measured in more.

02 / REACH
Coverage
12-18Sq.Ft/Kg
03 / VALUE
Price per sq. ft.
₹ 1per sq. ft.
THE SALES STORY

Why Customers Should Select Watertite Waterproof Wall Putty

Why a Dealer Should Recommend Watertite Waterproof Wall Putty

  • Recommend where water repellency and salt-deposit resistance suit the wall.
  • Justify preparation through silicone additives, whiteness and finish-system benefits.
  • Estimate from current coverage, thickness and required coats.
  • Verify GreenPro and warranty conditions before using them in the sale.

Key Facts

FinishMatt / Smooth Finish
Pack sizes40Kg, 20Kg, 5 Kg & 1 Kg
ApplicationPutty Knife or Trowel

Application Journey

Full application notes
01
Prepare

Pre-application surface preparation

1. Remove all loosely adhering material such as dirt, dust, grease, fungi, algae, flaking paint and oil.

02
Apply

Application procedure

1. Apply the first coat uniformly on the pre-wetted substrate using a putty blade or steel trowel.

03
Dry & care

Drying, recoat and working time

Drying performance may vary with climatic conditions, temperature, humidity and surface condition.

GOOD TO KNOW

Questions customers ask

Open a question to see the answer.

Why does Watertite Putty show a Lotus Bead effect?
Its cured surface is designed to provide high water repellency, creating the stated Lotus Bead hydrophobic effect.
Do I need to apply primer before Watertite Waterproof Putty?
Normally no. The label states that no priming is required before putty application. For damp interior areas, however, the dampness source should first be rectified and Jewell Damproof Primer used as specified.
Can I sand Watertite Putty like normal wall putty?
Only gently. The label warns against strong rubbing with rough emery paper because it can reduce the water-repellency properties.
How long can the mixed putty be used?
The stated pot life is approximately 3.0-3.5 hours.
How thick should the two putty coats be together?
The total thickness of both coats should be limited to a maximum of approximately 1.5 mm.
How long should I wait before applying paint over the putty?
The label recommends allowing the surface to dry completely, preferably about 24 hours depending on climatic conditions, before applying the topcoat.
FULL PRODUCT KNOWLEDGE

Detailed product information

Open a topic for the complete wording from the product document.

Product story

Product description

Jewell Watertite Waterproof Wall Putty is a premium quality powder putty specially designed with silicone and anti-efflorescence additives to provide waterproofing properties and efflorescence resistance.

It is developed as a base coat to cover unevenness and pinholes in plastered surfaces and to prepare walls and ceilings for painting. The formulation contains quality minerals, white cement, redispersible polymers and special additives to improve adhesion to the surface.

The product is suitable for both interior and exterior surfaces and is designed to provide a smooth finish, water repellency and extended life to subsequent topcoats.

Product positioning

Jewell Watertite Waterproof Wall Putty is positioned as:

A premium waterproof wall putty for interior and exterior walls

A base coat for levelling uneven plastered surfaces and filling pinholes

A putty with water-repellent and anti-efflorescence performance

A high-whiteness wall preparation product

A smooth, easy-to-apply base for subsequent paint systems

A product designed to support resistance to peeling, blistering and hairline cracking

Key product claims

Water Repellency

Anti-Efflorescent

Vibrant White Whiteness

Waterproofing Warranty

Resists Peeling, Blistering and Cracking

Aesthetic Finish

Ease of Application

For Interior and Exterior Walls

GreenPro Certified

Key features and benefits

Cured putty provides excellent hydrophobicity with a Lotus Bead effect

Provides anti-efflorescence performance compared with traditional powder putties

Offers best-in-class whiteness compared with normal white cement-based putties

Provides a seamless finish with pinhole-filling capability and butter-like smoothness

Mixed paste is light and requires less effort during application

Helps resist peeling, blistering and hairline cracking

Supports adhesion of subsequent topcoats

Consumer / applicator benefits

Water Repellency, Anti-Efflorescence, Vibrant Whiteness, Resists Peeling, Blistering and Cracking, Smooth Aesthetic Finish, Easy Application, Interior and Exterior Use, Waterproofing Warranty

Consolidated product brief

Jewell Watertite Waterproof Wall Putty is a premium white powder putty for interior and exterior wall preparation. It is formulated with silicone, anti-efflorescence additives, minerals, white cement, redispersible polymers and special additives.

The product provides water repellency, anti-efflorescence performance, smoothness, high whiteness and good adhesion while helping prepare uneven plastered walls and ceilings for painting.

For application, the label specifies 30-40% clean water, mechanical mixing for about 3-5 minutes, a pot life of 3.0-3.5 hours, two coats within a total maximum thickness of 1.5 mm, and careful non-aggressive finishing to preserve water-repellency.

Application & care

Pre-application surface preparation

1. Remove all loosely adhering material such as dirt, dust, grease, fungi, algae, flaking paint and oil.

2. Use emery paper, a putty blade or wire brush as required.

3. Use water jetting where necessary to remove remaining contamination.

4. Pre-wet the surface using a brush, hose-pipe spray, mug or similar method.

5. Keep the surface adequately wet during putty application.

Mixing of waterproof putty

1. Use clean water for mixing.

2. Slowly add 1 kg of Jewell Watertite Waterproof Putty with 30-40% clean water, approximately 300-400 ml per kg.

3. Add water gradually in small quantities to the putty; do not pour the putty into water.

4. Mix preferably with a mechanical stirrer for approximately 3-5 minutes until a creamy consistency is achieved.

5. Continue mixing until a uniform paste is formed.

6. Allow the mixed paste to rest for approximately 5 minutes.

7. Use the prepared paste within approximately 3.0-3.5 hours.

Application procedure

1. Apply the first coat uniformly on the pre-wetted substrate using a putty blade or steel trowel.

2. Apply the paste from the bottom of the substrate in an upward direction to reduce wastage.

3. Ensure the substrate temperature does not exceed 40°C during application.

4. After the first coat dries, gently rub the surface with a wet sponge or very gently with a putty blade to remove loose particles.

5. Allow the surface to dry for at least 3-4 hours.

6. Apply the second coat of Watertite Waterproof Putty.

7. Allow the surface to dry completely.

8. Keep the total thickness of both coats within a maximum of 1.5 mm.

Topcoat application

Allow the putty surface to dry fully before applying subsequent topcoats.

The label recommends preferably allowing about 24 hours before topcoat application, depending on climatic conditions and complete surface dryness.

Apply the required topcoat over the prepared and primed surface according to the topcoat's own application procedure.

Maintain topcoat coverage according to the relevant product data sheet.

Drying, recoat and working time

Drying performance may vary with climatic conditions, temperature, humidity and surface condition.

Technical reference

Waterproofing warranty

The product carries a 2-year waterproofing warranty on dampness when used with Jewell Damproof Primer in interior applications, subject to the stated system and applicable warranty conditions.

Recommended usage

Interior walls

Exterior walls

Plastered wall surfaces

Ceilings

Uneven plastered surfaces

Pinholes and minor surface irregularities

Technical specifications

Coverage varies with surface texture and condition. The label and catalogue express coverage differently, so both source values are retained.

Sanding and surface finishing

Do not rub the waterproof putty strongly with rough emery paper.

Aggressive sanding can break the film and reduce water-repellency properties.

If levelling is required before topcoat application, use very fine waterproof emery paper of not less than 400 number.

The finished surface should be smooth and ready for the next coating stage.

Priming guidance

No priming is required before application of the putty under normal conditions.

For interior damp areas, first stop the source of dampness.

After rectifying the source of dampness, seal the surface with Jewell Damproof Primer before applying Watertite Waterproof Putty to achieve the intended waterproofing performance.

Application restrictions

Do not apply when immediate rain is forecast.

Do not apply on surfaces with unresolved dampness or active water ingress.

Do not use mixed paste after the stated pot life has expired.

Do not exceed 40°C substrate temperature during application.

Do not exceed the stated maximum total thickness of 1.5 mm for both coats.

Do not aggressively sand the final waterproof putty surface with rough emery paper.

Health, safety and environmental information

No added Lead, Mercury and Chromium compounds

Lead content in dried paint film does not exceed 90 parts per million

Sanding, burning or other treatment of paint films may generate hazardous dust and fumes

Use wet sanding or suitable low-dust methods where possible

Work in well-ventilated areas

Use suitable personal protective equipment

Wear eye and hand protection

Do not breathe vapour or spray

If the product contacts eyes, rinse immediately with plenty of water and seek medical advice

If the product contacts skin, wash immediately with soap and water or a suitable skin cleanser

Do not use solvents or thinners for skin cleaning

Do not empty into drains or water courses

Do not use empty bags for storing food

Keep out of reach of children

Store in a well-ventilated place

Dispose of contents and bags in accordance with applicable regulations

Downloads

02 / CREATIVES0 files

Creatives

Visuals to support your sales conversations.

No files added yet.

03 / VIDEOS0 files

Videos

Product stories and demonstrations.

No files added yet.


PRODUCT FINDER

Find a product

Explore products by series, category or surface, or search by name.

PRODUCT LIBRARY

Browse the collection

Choose a product type, then narrow your selection.